404

[ Avaa Bypassed ]




Upload:

Command:

botdev@18.219.103.116: ~ $
/* SPDX-License-Identifier: GPL-2.0 */
#ifndef __LINUX_SPI_GPIO_H
#define __LINUX_SPI_GPIO_H

/*
 * For each bitbanged SPI bus, set up a platform_device node with:
 *   - name "spi_gpio"
 *   - id the same as the SPI bus number it implements
 *   - dev.platform data pointing to a struct spi_gpio_platform_data
 *
 * Or, see the driver code for information about speedups that are
 * possible on platforms that support inlined access for GPIOs (no
 * spi_gpio_platform_data is used).
 *
 * Use spi_board_info with these busses in the usual way, being sure
 * that the controller_data being the GPIO used for each device's
 * chipselect:
 *
 *	static struct spi_board_info ... [] = {
 *	...
 *		// this slave uses GPIO 42 for its chipselect
 *		.controller_data = (void *) 42,
 *	...
 *		// this one uses GPIO 86 for its chipselect
 *		.controller_data = (void *) 86,
 *	...
 *	};
 *
 * If chipselect is not used (there's only one device on the bus), assign
 * SPI_GPIO_NO_CHIPSELECT to the controller_data:
 *		.controller_data = (void *) SPI_GPIO_NO_CHIPSELECT;
 *
 * If the MISO or MOSI pin is not available then it should be set to
 * SPI_GPIO_NO_MISO or SPI_GPIO_NO_MOSI.
 *
 * If the bitbanged bus is later switched to a "native" controller,
 * that platform_device and controller_data should be removed.
 */

#define SPI_GPIO_NO_CHIPSELECT		((unsigned long)-1l)
#define SPI_GPIO_NO_MISO		((unsigned long)-1l)
#define SPI_GPIO_NO_MOSI		((unsigned long)-1l)

/**
 * struct spi_gpio_platform_data - parameter for bitbanged SPI master
 * @sck: number of the GPIO used for clock output
 * @mosi: number of the GPIO used for Master Output, Slave In (MOSI) data
 * @miso: number of the GPIO used for Master Input, Slave Output (MISO) data
 * @num_chipselect: how many slaves to allow
 *
 * All GPIO signals used with the SPI bus managed through this driver
 * (chipselects, MOSI, MISO, SCK) must be configured as GPIOs, instead
 * of some alternate function.
 *
 * It can be convenient to use this driver with pins that have alternate
 * functions associated with a "native" SPI controller if a driver for that
 * controller is not available, or is missing important functionality.
 *
 * On platforms which can do so, configure MISO with a weak pullup unless
 * there's an external pullup on that signal.  That saves power by avoiding
 * floating signals.  (A weak pulldown would save power too, but many
 * drivers expect to see all-ones data as the no slave "response".)
 */
struct spi_gpio_platform_data {
	unsigned	sck;
	unsigned long	mosi;
	unsigned long	miso;

	u16		num_chipselect;
};

#endif /* __LINUX_SPI_GPIO_H */

Filemanager

Name Type Size Permission Actions
ad7877.h File 835 B 0644
adi_spi3.h File 15.1 KB 0644
ads7846.h File 2.02 KB 0644
at73c213.h File 828 B 0644
at86rf230.h File 724 B 0644
cc2520.h File 620 B 0644
corgi_lcd.h File 460 B 0644
ds1305.h File 1.08 KB 0644
eeprom.h File 1.19 KB 0644
flash.h File 1023 B 0644
ifx_modem.h File 616 B 0644
l4f00242t03.h File 847 B 0644
libertas_spi.h File 907 B 0644
lms283gf05.h File 775 B 0644
max7301.h File 939 B 0644
mc33880.h File 196 B 0644
mcp23s08.h File 685 B 0644
mmc_spi.h File 1.91 KB 0644
mxs-spi.h File 5.24 KB 0644
pxa2xx_spi.h File 1.5 KB 0644
rspi.h File 715 B 0644
s3c24xx.h File 816 B 0644
sh_hspi.h File 572 B 0644
sh_msiof.h File 357 B 0644
spi-fsl-dspi.h File 955 B 0644
spi.h File 50.33 KB 0644
spi_bitbang.h File 1.43 KB 0644
spi_gpio.h File 2.56 KB 0644
spi_oc_tiny.h File 628 B 0644
tdo24m.h File 210 B 0644
tle62x0.h File 660 B 0644
xilinx_spi.h File 627 B 0644